Cable tool / Rotary / Auger/ Related items

Superior Rig Systems for Cable Tool /Rotary / Auger WANTED : All makes and models of used drilling rigs

((( NEW LISTING /MOTIVATED SELLER !!!!!! )))) THESE RIGS ARE PRICED TO SELL      2 Rig Turnkey Package ,Drill ready . 1- Ideco H35 Rotary Drilling rig ,1- Ideco H37 Rotary Drilling rig , Will sell individually if buyers for both rigs .

2 Rig TURNKEY DRILL READY PACKAGE CONSISISTING OF 2 Ideco Rotary Drilling Rigs .Both rigs were drilling this year .Selling only due to closinging Business .

FIRST RIG ;

Ideco H35 Rotary Drilling Rig ,Rated at 8-3/4 hole at 6,000 feet .

Ideco H35

250,000 pound ton hook , 500 hp Detroit diesel 60 Series with a New Reman Allison transmission , 12 ' kb with 20-1/2 inch Rotary table , 12-6-1/2 inch Drill Collars , 11 inch 3,000 # BOP Stack , 5,000 feet of 4-1/2 inch XHOLE Drill rod , 30 foot long joints ,75% of drill rod is double band ,Derrick height is 102 feet .National C250 Duplex mud pump with DD 60 Series engine with fresh overhaul.

RIG 2

Ideco H37 Rotary Drilling Rig ,Rated at 8-3/4 hole at 8,000 feet

All new tires , Kelly hose, and hydraulic hoses ,300,000 # Ton hook load , fresh Rebuilt Detroit 60 Series diesel engine with Allison transmission , free standing 108 foot Crown Derrick ,fitted for Tesco HMI 250 Top drive ,14' kb with 20-1/2 inch Rotary table ,12-6-1/2 inch Drill collars , 11 inch -3,000 # BOP Stack ,5,000 feet of 4-1/2 drill rod ,2-F800 Triplex mud pumps.

Additional items :

1 set fully working steel pits with double Vortex shakers

1Stripped set of steel pits that are ready to be refurbished .All motors , pumps and stirrers are included

2-Double Vortex shakers for pits

1-F800 Triplex mud pump

1- National C250 Duplex mud pump

Fuel trailer with 2-Cat 400kw Generators

Fuel skid for earth pit drilling with closing unit , and 100kw Generator

Spare Rotary table

2 Half rounds for closed loop system drilling

2 Tool houses FULL of spare parts for EACH RIG

There are also lots of spare items that aren't even listed that go with the rigs .

Note ; H35 Rig consists of about 11 Loads , this rig is in Illionois

H37 Rig Consists of about 18 Loads , this rig is located in Ohio

RIGS ARE DRILL READY

Turnkey package is priced at $665,000.00

(( SALE PENDING )) PRICED TO SELL $605,000.00 )) 2007 Atlas Copco RD20 , 120,000 pounds pull back , on a 5 axle Carrier with a Cat C13 carrier engine and a Cummins QSK ,625 hp Deck engine , comes with 3,000 feet of 4-1/2 Drill Rod .

 2007 Atlas Copco RD20 ,Rig serial number is 21057 .Top head drive , 2 motorspur gear on Rotary Head ,120,000 pounds pull back .SUPER CLEAN RIG .5 axle Carrier with a Cat C13 Diesel engige . The Deck engine is a Cummins QSK ,625 hp diesel engine , has a Atlas Copco1250cfm/350psi air compressor,and at additional cost, 2- 1170/350 skid mounted base with a Cat C15 diesel engines are available to drill dipper and faster at $55,000.00 each

Package comes with 3,000 feet of 4-1/2 inch Drill Rod ,30 foot lengths , with 2-7/8IF Pin .Drill Rod is still 75-80% to true OD .Addittional drill rod is available at cost of $450.00 per 30 foot rod .Other equipment available .

Seller has enough equipment for this rig  to be a Drill Ready !!!!!

PRICED TO SELL AT $605,000.00

Located in Hagerstown Md.

(( NEW LISTING )) PRICED TO SELL  ,ONLY $12,000.00 for both rigs  2-Walker Neer model S 32 Cable tool drilling rigs ,rated 6 inch hole at 2,500 feet

 PRICED TO SELL

2- Walker Neer  model S32 Cable tool drilling rig ,7X8 Double Pole ,55 foot derrick 1 had been  running , 1 was for a good parts rig .Good rig has a Waukesha deck engine & 3 hydraulic Jacks . Serial numbers ar  1419 &1426

PRICED TO SELL $12,000.00 FIRM

Located in Southern Illinois 

(( NEW LISTING )) PRICED TO SELL , $15,000.00  Walker Neer model S43 Cable tool Drilling rig Rated at 8 inch hole at 3,500 feet

 PRICED TO SELL

Walker Neer S43 Cable tool drilling rig , Serial number is 1372. 7X8 double pole, 65 foot , rated at 8 inch hole at 3,500 feet .has a Deutz 5 Cylinder air cooled diesel deck engine ,was running when parked , but had bad fuel , and has fuel injectors and pump issues ,Has 4,000 feet of 3/4 inch drill line ,and  4,000 feet of sandline .more pictures to follow .

PRICED TO SELL $15,000.00

Located in West Virginia

(( NEW LISTING )) PRICED TO SELL  !!!!!!!!  Speedstar Series 3000 Top Head Drive on a 1969 Peterbuilt

 Speedstar Series 3000 Top head Drive ,Rig has drilled 3,000 foot oil wells.Very solid unit , it will run Range 2 Casing ,has yhdraulic pumps redone ,Has a Cummins 400 diesel engine .The unit need the following items ,needs truck tires and some hydraulic hoses replaced ,and air compressor,has retractable Rotary table .Also drilling related items are available .

Also have 2,325 feet of 4-1/2 inch drill rod ,2-7/8IF thread in 25 foot joints AVAILABLE .

PRICED TO SELL $37,500.00

Located in West Virginia

(( NEW LISTING )) PRICED TO SELL !!!!!!!      1968 Cooper 15 Single Drum Service Rig ,Unit will pull Range 2 Casing

 NICE Cooper 15 ,Single drum service rig ,was used on 2,000 foot wells .6X8 Single pole , friction Clutches,High & Low Speed ,3 speed reverse .Mounted on a 1991 GMC Topkick .

PRICED TO SELL $28,500.00

Located in West Virginia

((( PRICE REDUCED TO $38,000.00))) Bucyrus Erie model 36L Old style ,54 Foot derrick ,High & Low Clutches ,Casing Strut.NOTE will also sell rig less Braces ,Engine  & PTO .Buyers choice !

 Bucyrus Erie 36L ,Old Style , 54 foot derrick ,good braces , Casing Strut ,High & Low Clutches , pinions still have squareness on them ,Lever Controls , the Slider pinions that shift Bull reel drum and Casing drum have wear , but still work fine , deck engine is a Cummins 6 cylinder diesel 8.3 Turbo , plenty of power ,the rig has powered hydraulis from a 50 gallon tank & currently , just a 1 section hydraulic port . Rig comes with  a 17 inch triple sheave Casing Block ,has approximately 1,000 feet of good sand line ,drill line and casing line should be replaced , but owner has just completeled 2 wells before parking rig .This rig has been used for drilling water wells .The rig comes with no Tooling. I have some tooling available in the state of Washington though , if interested .

The price of rig is $38,000.00

Located in Madera California

((((PRICE REDUCED $10,500.00 !!! )))) 24 Loomis / jack shaft pinions and gears are great condition , on 1973 Chevy

 PRICE REDUCED !!!

24 Loomis , great condition jack shaft gears and pinions with very little wear ,4 cylinder International gas engine with 4 speed transmission with reverse , approximately 800 feet of 3/4 inch drill line , approximately 800 feet of 7/16 inch sand line , cat heads , heavy derrick , mounted on a 1973 Chevy , single axle in good condition.

Price reduced to $10,500.00

Located in Kentucky

(( OPEN TO SERIOUS OFFERS ))2002 Bowman 2.5 Power swivel unit with hydraulics ,powered by a 4 Cylinder Cummins Turbo diesel engine ONLY 2,200 hours

Bowman 2.5 Power Swivel Unit mounted on trailer ,Cummins 4 cylinder turbo diesel engine .ONLY 2,200 hours on the Unit .Unit in very good codition

$50,000.00

Located in Kentucky

1 LOT OF CABLE TOOL DRILLING TOOLS,for sale as package ***Majority of tooling is 2-3/4 X 3-3/4 Pin ,and larger bits are 4X5 pin .

1 Lot of Cable tool drilling tools in assorted pin sizes.Items OPEN TO SERIOUS OFFERS

Large Bailers 8,10 12,14 inch , large scows 8,15, & 17 inch .6-20 Drive Heads.16 & 20 inch Perfrators ,10-24 inch bits , most bits are 4X5 Pin ,Cable spears , overshot sockets , J Wrenches ,drilling jars , fishing jars , rope sockets , mixing sub , Casing bowl and slips ,6,8,& 10 inch cylinders cylinders , Homemade line up clamps for welding pipe . Some BE 28L Sheaves .

 and lots of  misc . items .

SOLD ONLY AS PACKAGE

Located in Pima Az

(( OPEN TO SERIOUS OFFERS)) 2-JOY WB Boosters 1,000PSI with Joy900/300 Air compressors ,with REMANUFACTURED CAT 3406 B Engines ,only abou 900 hours

NOTE THE FOLLOWING .

1 Booster and compressor runs fine .

1 Cat 3406 on a Joy 900/300 Compressor has fuel injector problems , they are clogged up from bad fuel .That is why this unit is $11,000.00 less .

2-Mid 1990's Joy WB12 Boosters 1,000 ps wit JOY 900/300 Compressors with REMANUFACTURED CAT 3406-B engines ,only approximately 900 hourss mounted on 48 foot oil field flat bed trailers .

1 Booster with compressor is $36,500.00

1 Booster running but needs injector pump work cleaned is $25,500.00

They need Batteries and 1 starter 

Located in Kentucky

PRICED VERY FAIR

(( OPEN TO SERIOUS OFFERS )) 2002 IR1070/350 Air compressor with Cat 3406-B with Ariel JG Ariel Booster 1,270 PSI with a 2004-2007 Cat C7 Electronic engine ,both engines have around 3,000 hours

(((( NOTE THE FOLLOWING ))))

The Cat3406B on the IR 1070/350 Runs fine . The Cat C7 engine has clogged up fuel injectors from bad gas .

Mounted on a 45 foot flat bed trailer ,with cat walks .

$55,000.00

Located in Kentucky

PRICED VERY FAIR

(((((( OPEN TO SERIOUS OFFERS ,LOOKING FOR SERIOUS BUYER )))))) LEFT HAND THREAD STEEL CABLE TOOL RIG CASING ,used for setting and reusing , has Square threads , does not have wrench flats

LEFT HAND THREAD CASING /High tensile strength IN THE FOLLOWING SIZES AND LENGTHS

CASING IS AMERICAN MADE

 ((((CASING HAS SQUARE THREADS))))

564 feet of 8-5/8 INCH  

625 feet of 11-7/8 INCH 

257 feet of 13-3/8 INCH 

will sell by size or package deal including all the pipe racks if wanted .

Located in Pasco Washington

((( SOLD )))) Pinnacle LHT 10-3/4 Casing ,4140 steel , .500 inch wall  with wrench flats for Rotary rig .825 feet

Todays cost for 825 feet would be $233,543.25 ,plus current tarriffs .Priced at $93,417.00

 Seller would sell 400 foot at one time ,no smaller amount though .

Located in Pasco Washington

(((( SOLD))))***** DRILL READY RIG ))***** 2007 Foremost DR-24 Dual Rotary Rig , C15 Cat Twin turbo diesel engine ,900-1070CFM/350PSI air compressor,low hours on air compressor . mounted on a KW T800                                       **NOTE **Will consider selling all of the LHT 4140 Steel Casing in package price ,barely used and some pipe never been ran .Priced at 62 cents on the dollar .Just the casing alone at todays cost would be $678,000.00 ,before tariffs . This is a great rig package for the money and plenty of drill steel ,some also new!

NOTE*****WILL NOW SALE ALL OF THE LHT CASING IN A PACKAGE PRICE ******

2007 Foremost DR24 Rotary rig ,Cat C15 twin turbo diesel engine ,81,071 miles  ,3,469 hours on air compressor .1070 cfm/350 psi.All good tires ,almost Brand new front tires .Complete sets of Driver & Breaker jaws ,6-24 inch .New 40 foot of 5 inch discharge hose .Brand new spare Main pull down cylinder ,and new spare radiator for air compressor ,Drill pipe ,casing, hammers ,stabilizers ,bits ,etc .CALL FOR PRICING/ MANY MORE PHOTOS AVAILABLE

Located in Pasco  Washigton

(((( SOLD )))) Bucyrus Erie model 60L Casing strut with sheaves

 $3,00.00

Located in Pasco Washington

((((SOLD )))) Bucyrus Erie 60L , 4 hydraulic jacks , 4  cylinder Perkins diesel,Casing Strut , mounted on a 1992 Kenworth T600 *****((((NOTE ,THIS RIG HAS THE SWABBING ATTACHMENT EQUIPMENT OPTION,speed reducer ideal for Swabbing )))

************ NOTE*****************

The rig now comes with the 3 New spools of drill line , sand line , casing line.Todays cost would be over $7,500.00

************************************Bucyrus Srie 60L Serial number 115527 ,NOTE --Spudding pinion has wear ,and no Casing line .

Perkins 4 cylinder diesel , cat heads , Casing Strut ,approximately 600 feet of 3/4 inch drill line , approximately 1,200 feet of 1/2 inch sand line , The rig has side guards , (4) Hydraulic jacks , 2 rear mounted jacks , 2 Hydraulic jacks behind the cab ,Hydraulic heel shoe brake , solid rig , solid walking beam . Mounted on a 1992 Kenworth T600 ,Detroit Diesel S60 Series engine ,Fuller transmission ,282,535 mileage .

NOTE-----The rig will come with a rope socket ,short stem , 3 bit ,jars ,J wrenches, single sheave casing block .

****Items available at additional cost****

Various sizes of  ,Jars ,bits etc.

*********OPTIONAL*******

1-LIKE NEW McKissick 12 inch triple sheave block ONLY $3,000.00

Plus various size bits and jars

Located in Pasco Washington

******NOTE THE FOLLOWING******

New Hendrickson Walking Beam Bushings 06/17  $2,746.96

New front passenger dual tires 05/17   $915.06

Rebuilt deck engine radiator 12/14

$390.96

(( SOLD ))1971 Bucyrus Erie 60L , SN#1323XX 4 hydraulic jacks , 4 cylinder diesel , mounted on a 1976 Ford

1971 Bucyrus Erie model 60L ,SN#1323XX ,approximately 1,000 feet of 3/4 inch drill line , approximately 1,600 feet of 2/1 inch sand line  ,SPUDDING PINION teeth are  real square , 90% ,Perkins 4 cylinder diesel 1,481 hours on meter ,Very solid walking beam , hydraulic Brake shoe ,Cat heads , 4 HYDRAULIC JACKS , 2- rear ,2 behind the cab .15 Ton MkKissick single sheave block ,frame als has enclosed guards for safety .Mounted on a 1976 Ford ,391 gas engine ,truck is in good condition , only 70,000 miles ,older tires though .

**** Rig comes with a socket , short stem , bit , jars , J wrenches .

other tooling at additional cost 60L Casing Strut is $3,000.00

******CONTACT FOR MORE PHOTOS ******

Located in Pasco Washigton 

((( SOLD ))) Bucyrus Erie 60L with casing strut ,Deutz 4 cylinder air cooled diesel engine mounted on a single axle ,WITH TOOLING

 Bucyrus Erie 60L with casing strut ,good braces ,pretty square spudding pinion , Deutz 4 cylinder air cooled diesel deck engine , drilled last approximately 10 years ago ,it had put on 2,000 feet of 3/4 inch drill line ,and 1,755 feet of 9/16 inch sand line .mounted on a single axle .Comes with string of tools along with additional tooling .

(((((TOOLING LIST NOW IN PHOTOS ,I CAN ALSO EMAIL YOU THE LIST )))))

Located in Ohio

$34,500.00

(( SOLD )) ChemGrout CG-500 Versatile Series 15 Gallon Double Hopper 

 MODEL CG5003C6DH Approximately 10 year old Grouter System , minimum  useage .15 Gallon double hopper , 18 hp. Kabota engine , 3 stage pump .$22,000.00

NEW COST IS $40,400.00

Located in Pasco Washington

(((( CURENTLY OFF MARKET ))))      Walker neer C43A , Air clutches on all 3 drums ,6 cylinder 250 Cummins diesel engine ((RIG IS SET UP TO USE ROTARY SWIVEL ))

NEW LISTING 

Walker Neer C43A cable tool drilling rig ,air clutches on all 3 drums ,60 foot derrick ,6 cylinder Cummins 250 diesel engine , has been mostly used for clean outs and servicing wells , tandem axle ,3rd leg , rig is set up to use swivel for rotary drilling , tandem axle , some thin metal gaurds and covers have rust holes in them ,the main frame and structure of the rig is solid , rig has been used on a 4,400 foot well .

Unsure  of the amount of drill line and sand line .

(((MANY OTHER PHOTOS AVAILABLE AND VIDEO OF DECK ENGINE RUNNING )))

Located in Ohio

(((( SOLD )))),ALSO COMES WITH EXTRA TOOLING****1972 Bucyrus Erie Series III SN 1335XX

NEW LISTING   Same owner over 35 years .

  1972 Bucyrus Erie 22W Series III ,SN 1335XX , COMPLETE WITH TOOLING . 6 Cylinder Continental Red Seal Propane engine with 120 gallon tank , good spudding pinion , hydraulic derrick hoist , 3-Hydraulic jacks,2-rear , 1 front ,split rim heel & beam sheaves , cat heads ,New 800 feet of 3/4 inch drill line , 700 feet of 3/8 inch sand line , straight braces , VIDEO AVAILABLE OF RIG DRILLING .

Mounted on a 1969 GMC 7500 , gas engine , newer clutch , 5X4 manual transmission ,tandem axle , hydraulic brakes.

****** COMES WITH THE FOLLOWING TOOLING *******

Most tooling is 2-1/4 X 3-1/4 pin ,some 2 x 3 pin tooling

Socket , stem ,8& 10 inch bits , wrenches , combination socket , 8 inch drive head , drill & fishing jars , bailers , sand pump , 4,5,&6 inch trip spears ,and misc. items .

((((ALSO COMES WITH EXTRA TOOLING))))

$36,000.00

Located in Whitefish Montana

(((( SOLD ))))Walker neer C43 , 6 cylinder International diesel engine , tandem axle with air brakes

NEW LISTING 

Walker Neer C43 cable tool drilling rig  ,60 foot derrick ,6 cylinder International diesel engine , has been mostly used for clean outs and servicing wells , tandem axle , some thin metal gaurds and covers have rust holes in them ,THE MAIN FRAME OF THE RIG AND STRUCTURE IS SOLID

Unsure  of the amount of drill line and sand line .

(((MANY OTHER PHOTOS AVAILABLE AND VIDEO OF DECK ENGINE RUNNING )))

Located in Ohio

( SOLD ) Bucyrus Erie 22W Series II , SN 123972 mounted on a 1985 Chevy

Bucyrus Erie 22W Series II , serial number 123972 , 4 Cylinder John Deere Model 4540 water cooled diesel . 2-BRAND NEW CLUTCHES STILL IN BOX , Good spudding pinion , at least 50 % squareness , Crown sheave has new pin & bearings , Derrick hoist rebuilt & replaced tear drop bushings , Newer shock kit with guide pin & bushing , 2-Rear Hydraulic jacks , cat heads , tool guide , Split rim heel & beam sheaves , sheaves have been rewelded up ,Newer 800 feet of 3/4 inch drill line , 800 feet of 3/8 inch sand line , lots of money spent on repairs .Mounted on a 1985 Chevy truck , single axle , 366 gas engine , 5/2 speed manual transmission , air brakes , under CDL limit .

Comes with the following tooling :

Burns open side socket , 18 & 23 foot stems , 6-15 inch bits , 3 bailers , circle jack , 2 - J wrenches , heavy duty drive clamps , tooling is a mix of 2-1/4X3-1/4 & 3-1/2X4-1/2 pin size .

Located in Georgia

$23,500.00

(( SOLD )) Bucyrus Erie 22W with 3 hydraulic jacks

Bucyrus Erie 22W Series 1 ,(( 3 hydraulic jacks )) , 90 % squareness on spudding pinion teeth , straight braces , 6 cylinder diesel water cooled engine , some surface rust , sand line is probably ok ,if couple layers taken off ,will need new drill line , engine starts right up , but rig has been sitting for awhile .

Mounted on a GMC Topkick , diesel engine ,it does run , but not in very good condition .

NOTE 

tooling available at additional cost

Located in Oklahoma

Priced at $23,500.00

(((SOLD))) 71 Speedstar ,3-Hydraulic jacks on low mileage 1991 International

71 Speedstar ,3-Hydraulic jacks ,Continental F162 Flat head  4 cylinder  gas engine  with electronic ignitionwith a newer long block ,tool guide , cat heads , approximately 600 feet of 3/4 inch drill line ,older sand line.Mounted on a 1991 International single axle ,low miles , almost new tires , hydraulic brakes , DT466 diesel engine , 5 speed transmission .rig is drill ready .

COMES WITH TOOLING : socket , stem ,jars ,5-10 inch bits , J wrenches ,drive clamps .Tools are 2X3 pin & box .

Located in Wisconson

((( SOLD ))) 1989 Speedstar SD300 Rotary rig with Air & Mud and Hammer

1989 Speedstar SD300 ,Joy 750/250 Air compressor ,under 1,000 hours on it , 3X4 Mission Mud Pump , no carrousel ,  mounted on a International with a 350 Cummins engine .This rig is drill ready . NO DRILL PIPE INCLUDED .

Has had the following updates :

Jefco repair September ,Engine replaced with a Cummins BCIV 88NT 350HP .( Less than 10 hours run since installed )

July 2018-XJB-5-251-825 Valve kit

2013 Rebuilt Derrick Cylinders

2012 Rebuilt Hydraulic Motors

2009 Rebuilt Top Head Swivel

2015 NEW 750/250 psi Air Compressor

Located in Minnesota

(( SOLD )) Bucyrus Erie 60L mounted on a Single Axle

Bucyrus Erie 60l ,mounted on a single axle ,cat heads ,3 cylinder Detroit Diesel engine, engine runs good ,still squareness on spudding pinion , newer brake blocks ,solid rig , solid spudding beam , approximately 1,700 feet of 3/4 inch drill line , approximately 1,700 feet of 9/16 inch sand line .

Located in Kentucky

$31,500.00

((( SOLD ))) Bucyrus Erie 22W Series 1 , on single axle , super clean , GREAT Spudding pinion

Bucyrus Erie 22W Series I, GREAT Spudding pinion ,mounted on a single axle trailer with 5th wheel hitch , kept inside , straight braces , cat heads , approximately 350 feet of 3/4 inch drill line , approximately 350 feet of 3/8 inch sand line , Newer Waukesha 4 cylinder gas engine , cat heads , com .

comes with stem , jars , bailer ,2-1/4X3-1/4 pin size

Located in New Jersey

(( SOLD)) Bucyrus Erie 22W Series II with string of 6 inch tools mounted on a 1999 T300 Kenworth

Bucyrus Erie 22W Series II , serial number 126117 , 6 cylinder Continental gas engine ,split rim sheaves , tool boxes, welder , torches ,new crown bushings & bearings, ,new shock kit , new raising line , (( 4 hydraulic jacks  )) , tool guide , approximately 300 feet of 3/4 inch drill line , approximately 400 feet of 3/8 inch sand line** Spare Continental Red Seal engine with PTO & pulley , spare radiator  & misc. spare parts , ** worn main spudding gear and spudding pinion , 2-1/4X3-1/4 pin size Socket ,Stem , 6 inch bit & bailer **, a parts rig is available , mounted on a 1999 Kenworth T300 ,  Cat engine , Fuller 8 speed transmission , new tires , new pinion & rear seal , new windshield . **** OPEN TO SERIOUS OFFERS ****

Located in New York

((( PRICED TO SELL )))1966 IR T3 ,8-V71 Detroit diesl deck engine

1966 IR T3 ,single rod carousel ,Low hammer 6-1/4 bit , 2- stabilizer ,low air ,around 180 psi max. Almost 850 drill rod , 400-500 feet of it is new drill rod . 20 foot sections ,subs ,change over adapters  , wrenches ,extra bits ,extra 6-1/4 inch hammer ,and misc  .Ran  good when parked around 5 years ago.

Located in Kentucky .

((( SOLD ))) Bucyrus Erie 20W mounted on a 1996 International

Bucyrus Erie 20W ,bearing style jack shaft serial number 1218XX ,3 cylinder Mitsubishi air cooled diesel engine ,cat heads .Mounted on a 1996 International , DT466 ,SS water tank ,hydraulic brakes .

Located in Michigan

$13,500.00

((( Sold ))) Bucyrus Erie 20W mounted on a 2000 Chevy

Bucyrus Erie 20W , serial number 1389XX , Bearing style jack shaft , 4 cylinder Industrial gas engine , approximately 600 feet of 5/8 inch drill line , approximately 300-400 feet of 3/8 inch sand line ,mounted on a 2000 Chevy C6500 , gas engine , solid truck , will sell mounted or un mounted .

Located in Michigan

$11,500.00 rig only

((( SOLD )))Bucyrus Erie 22W Series III Rebuilt Jack Shaft )

Rebuilt 1972 Bucyrus Erie Series III ,6 cylinder Ford gas engine / low hours , Rebuilt jack shaft ,good spudding gear , new header slide blocks , Series III split heel & beam sheave , ( 4 HYDRAULIC JACKS ) approximately 600 feet of 3/4 inch drill line , approximately 600 feet of 3/8 inch sand line , NEW PAINT . Mounted on a 1990 GMC Top Kick , Cat 3116,210 hp diesel engine , 5 speed transmission , air brakes , good tires .

DRILL READY

STRING OF TOOLING INCLUDED .Socket , stem ,bit , bailer ,wrenches ,chain tightner , 2-1/4 X 3-1/4 Pin size

Located in New York

((SOLD)) Cyclone 43 Mounted on a 1995 International 4900

Mid 1970's Cyclone 43 with the following :

45 foot derrick , Hydraulic motor to raise the derrick-factory item , 4-Hydraulic jacks -THESE are the same hydraulic jacks that were used on the rotary rigs , hydraulic break out , 600 feet of New 3/4 Bethlehem drill line , 600 feet of 3/8 inch sand line , single sheave casing block .

Mounted on a 1995 International 4900 , Newer style hood , DT 466 diesel engine , real good cab .

****DRILL READY RIG****

STRING OF TOOLING INCLUDED . 2-1/4X3-1/4 pin size socket and stem ,adapter to 2X3 pin ,6 inch bit with 2X3 pin .

Located in New York

(( SOLD )) Bucyrus Erie 22W Series 1 mounted on a 1994 GMC Top Kick

Bucyrus Erie 22W Series 1 , John Deere 4 cylinder model 4219 Diesel engine with low hours , almost new spudding pinion ,Tool guide , newer shock kit , guide pin & bushing , newer belt , approximately 500 feet of 3/4 inch drill line , approximately 400 feet of 3/8 inch sand line . Same owner the last 20 years . Mounted on a 1994 GMC Top Kick , 3116 Cat diesel engine , 5/2 speed transmission ,good tires .

Comes with a socket , stem , 6 inch bit , and bailer .

Located in central Alabama

(( SOLD ))Bucyrus Erie 22W Series 1 mounted on a 1987 Ford F8000 DRILL READY ****WITH TOOLING

 Bucyrus Erie 22W Series 1 ,sn#1163XX  ,Approximately 250 feet of 3/4 inch drill line , approximately 250 feet of 3/8 inch sand line , newer spudding pinion , new steel made bull reel drum , tool guide , newer heel sheave , newer shock kit assy. , Stainless Steel fuel tank , Isuzu 4 Cylinder diesel deck engine .

Mounted on a 1987 Ford F8000 ,3208 Cat engine ,5 speed , 2 speed rear end ,tandem axle ,air brakes , good front and rear tires ,** engine does use some oil , but is a good running engine . Rig is sitting on a bed ,with 4 foot storage area between truck and rig for tools .

Comes with the following tooling :

Socket , stem ,2- 8 inch bits ,3-bailers ,J wrenches , drive clamps.

rig is DRILL READY

((( SOLD ))) $6,500.00 Cyclone model 30

Cyclone model 3 cable tool drilling rig , has a 15 foot derrick ,plus another 15 foot section , it will drive 20 foot pipe , elevator shaft drilling rig , small cable tool drilling rig ,3 line drilling rig ,Continental Red Seal 4 cylinder gas engine .

No tools

Located in Kentucky .

SOLD 71 Speedstar , 240- 6 cylinder ,running condition , will sell mounted orun mounted on a 6X6 DRILL READY

71 Speedstar ,240- 6 cylinder Industrial gas engine , approximately 2,500 feet of 5/8 drill line , approximately 2,500 of 3/8 inch drill line .1 cathead , casing strut , 2 jacks on the back , comes with 2 sets of tooling . 3 & 5 inch tooling , and wrenches , mounted on a 6X6 in good condition , drilling condition .  Located in Kentucky .

Waiting on more photos ,contact for information .

OFF MARKET Bucyrus Erie 60L mounted on a 1992 Kenworth

Bucyrus Erie 60L , rig is completely guarded , 4 cylinder Perkins diesel engine , 4 hydraulic jacks , really great condition rig ,mounted on a 1992 Kenworth ,Detroit Diesel , tandem axle .

Located in Washington

Priced at $57,500.00 FIRM PRICE

Can require additional photos for completely

serious buyer .Serious buyers can contact me on website contact page .

Walker Neer S33 (((( Currently off the market ))))

Waukesha 6 Cylinder
Waukesha 6-cylinder engine, good clutches, 900 feet of 7/8-inch drill line, 900 feet of sand line, triple sheave casing block, tandem axle, no rust, comes with a lot of tooling. Rope sockets, 4 stems, 3 jars, 6, 8, and 10-inch bits, mostly 3x4 pin size. Circle Jack, 4 pair of wrenches, rod elevators, manual spyder with inserts, and additional tooling. Rig is located in Texas, with the same owner for the last 30 years.