Cable tool / Rotary / Auger

Superior Rig Systems for Cable Tool / Rotary / Auger Drilling

1992 Gus Pech 48 Bucket / Auger Drilling rig ,mounted on a 1992 Mack

1992 Gus Pech 48 Bucket / Auger drilling rig , 48 inch rotary table , 100 Foot -4 piece telescoping kelly bar , 14,000 lb Aux. winch , 14,000 lb. kelly winch ,Hydraulic kelly push out , With optional Kelly bar crowd pull down attachment ,with a 4 cylinder Cummins diesel with its own fuel tank .

MOUNTED on a 1992 Mack ,6 cylinder Mack diesel ,13 speed transmission ,good tires ,last drilled about 4 years ago ,DOT specs approved ,road worthy unit , drill ready .Drilling attachments include a real good 36 inch bucket ,and a few core buckets .

Located in North Dakota

NEW LISTING *** Walker Neer C34 Cable tool drilling rig

Walker Neer C34 cable tool drilling rig ,  mounted on a tandem axle , 50 foot derrick ,7X8 double pole ,6 cylinder Waukasa propane engine ,approximately 3,000 feet of 3/4 inch drill line , approximately 3,000 feet of sand line ,cat heads , rig does have only surface rust , was ran last a couple years ago PICTURES TO FOLLOW ,the photo on disply is not the C34

Located in Oklahoma

((( PRICE REDUCED ))) NEW LISTING Bucyrus Erie 22W with 3 hydraulic jacks

Bucyrus Erie 22W Series 1 ,(( 3 hydraulic jacks )) , 90 % squareness on spudding pinion teeth , straight braces , 6 cylinder diesel water cooled engine , some surface rust , sand line is probably ok ,if couple layers taken off ,will need new drill line , engine starts right up , but rig has been sitting for awhile .

Mounted on a GMC Topkick , diesel engine ,it does run , but not in very good condition .

NOTE 

tooling available at additional cost

Located in Oklahoma

Priced at $23,500.00

Price reduced to $13,500.00 ))24 Loomis / jack shaft pinions and gears are great condition , on 1973 Chevy

 24 Loomis , great condition jack shaft gears and pinions with very little wear ,4 cylinder International gas engine with 4 speed transmission with reverse , approximately 800 feet of 3/4 inch drill line , approximately 800 feet of 7/16 inch sand line , cat heads , heavy derrick , mounted on a 1973 Chevy , single axle in good condition .

Located in Kentucky

(((SOLD))) 71 Speedstar ,3-Hydraulic jacks on low mileage 1991 International

71 Speedstar ,3-Hydraulic jacks ,Continental F162 Flat head  4 cylinder  gas engine  with electronic ignitionwith a newer long block ,tool guide , cat heads , approximately 600 feet of 3/4 inch drill line ,older sand line.Mounted on a 1991 International single axle ,low miles , almost new tires , hydraulic brakes , DT466 diesel engine , 5 speed transmission .rig is drill ready .

COMES WITH TOOLING : socket , stem ,jars ,5-10 inch bits , J wrenches ,drive clamps .Tools are 2X3 pin & box .

Located in Wisconson

((( SOLD ))) 1989 Speedstar SD300 Rotary rig with Air & Mud and Hammer

1989 Speedstar SD300 ,Joy 750/250 Air compressor ,under 1,000 hours on it , 3X4 Mission Mud Pump , no carrousel ,  mounted on a International with a 350 Cummins engine .This rig is drill ready . NO DRILL PIPE INCLUDED .

Has had the following updates :

Jefco repair September ,Engine replaced with a Cummins BCIV 88NT 350HP .( Less than 10 hours run since installed )

July 2018-XJB-5-251-825 Valve kit

2013 Rebuilt Derrick Cylinders

2012 Rebuilt Hydraulic Motors

2009 Rebuilt Top Head Swivel

2015 NEW 750/250 psi Air Compressor

Located in Minnesota

(( SOLD )) Bucyrus Erie 60L mounted on a Single Axle

Bucyrus Erie 60l ,mounted on a single axle ,cat heads ,3 cylinder Detroit Diesel engine, engine runs good ,still squareness on spudding pinion , newer brake blocks ,solid rig , solid spudding beam , approximately 1,700 feet of 3/4 inch drill line , approximately 1,700 feet of 9/16 inch sand line .

Located in Kentucky

$31,500.00

((( SOLD ))) Bucyrus Erie 22W Series 1 , on single axle , super clean , GREAT Spudding pinion

Bucyrus Erie 22W Series I, GREAT Spudding pinion ,mounted on a single axle trailer with 5th wheel hitch , kept inside , straight braces , cat heads , approximately 350 feet of 3/4 inch drill line , approximately 350 feet of 3/8 inch sand line , Newer Waukesha 4 cylinder gas engine , cat heads , com .

comes with stem , jars , bailer ,2-1/4X3-1/4 pin size

Located in New Jersey

(( SOLD)) Bucyrus Erie 22W Series II with string of 6 inch tools mounted on a 1999 T300 Kenworth

Bucyrus Erie 22W Series II , serial number 126117 , 6 cylinder Continental gas engine ,split rim sheaves , tool boxes, welder , torches ,new crown bushings & bearings, ,new shock kit , new raising line , (( 4 hydraulic jacks  )) , tool guide , approximately 300 feet of 3/4 inch drill line , approximately 400 feet of 3/8 inch sand line** Spare Continental Red Seal engine with PTO & pulley , spare radiator  & misc. spare parts , ** worn main spudding gear and spudding pinion , 2-1/4X3-1/4 pin size Socket ,Stem , 6 inch bit & bailer **, a parts rig is available , mounted on a 1999 Kenworth T300 ,  Cat engine , Fuller 8 speed transmission , new tires , new pinion & rear seal , new windshield . **** OPEN TO SERIOUS OFFERS ****

Located in New York

Shur-Hit 2 Line drilling rig made in Flint Michigan

 Shur-Hit ,2 line drilling rig ,Continental 4 cylinder lp engine ,3 hydraulic jacks ,mounted on a 1973 GMC gas engine , 4 speed , 2 wheel drive . 

UNIT WAS USED FOR PULLING PUMPS

LOCATED IN Michigan

OPEN TO OFFERS

1981 CP T700WH ,call for information for now .Pictures and information to follow

((( PRICED TO SELL )))1966 IR T3 ,8-V71 Detroit diesl deck engine

1966 IR T3 ,single rod carousel ,Low hammer 6-1/4 bit , 2- stabilizer ,low air ,around 180 psi max. Almost 850 drill rod , 400-500 feet of it is new drill rod . 20 foot sections ,subs ,change over adapters  , wrenches ,extra bits ,extra 6-1/4 inch hammer ,and misc  .Ran  good when parked around 5 years ago.

Located in Kentucky .

((( SOLD ))) Bucyrus Erie 20W mounted on a 1996 International

Bucyrus Erie 20W ,bearing style jack shaft serial number 1218XX ,3 cylinder Mitsubishi air cooled diesel engine ,cat heads .Mounted on a 1996 International , DT466 ,SS water tank ,hydraulic brakes .

Located in Michigan

$13,500.00

((( Sold ))) Bucyrus Erie 20W mounted on a 2000 Chevy

Bucyrus Erie 20W , serial number 1389XX , Bearing style jack shaft , 4 cylinder Industrial gas engine , approximately 600 feet of 5/8 inch drill line , approximately 300-400 feet of 3/8 inch sand line ,mounted on a 2000 Chevy C6500 , gas engine , solid truck , will sell mounted or un mounted .

Located in Michigan

$11,500.00 rig only

((( SOLD )))Bucyrus Erie 22W Series III Rebuilt Jack Shaft )

Rebuilt 1972 Bucyrus Erie Series III ,6 cylinder Ford gas engine / low hours , Rebuilt jack shaft ,good spudding gear , new header slide blocks , Series III split heel & beam sheave , ( 4 HYDRAULIC JACKS ) approximately 600 feet of 3/4 inch drill line , approximately 600 feet of 3/8 inch sand line , NEW PAINT . Mounted on a 1990 GMC Top Kick , Cat 3116,210 hp diesel engine , 5 speed transmission , air brakes , good tires .

DRILL READY

STRING OF TOOLING INCLUDED .Socket , stem ,bit , bailer ,wrenches ,chain tightner , 2-1/4 X 3-1/4 Pin size

Located in New York

((SOLD)) Cyclone 43 Mounted on a 1995 International 4900

Mid 1970's Cyclone 43 with the following :

45 foot derrick , Hydraulic motor to raise the derrick-factory item , 4-Hydraulic jacks -THESE are the same hydraulic jacks that were used on the rotary rigs , hydraulic break out , 600 feet of New 3/4 Bethlehem drill line , 600 feet of 3/8 inch sand line , single sheave casing block .

Mounted on a 1995 International 4900 , Newer style hood , DT 466 diesel engine , real good cab .

****DRILL READY RIG****

STRING OF TOOLING INCLUDED . 2-1/4X3-1/4 pin size socket and stem ,adapter to 2X3 pin ,6 inch bit with 2X3 pin .

Located in New York

(( SOLD )) Bucyrus Erie 22W Series 1 mounted on a 1994 GMC Top Kick

Bucyrus Erie 22W Series 1 , John Deere 4 cylinder model 4219 Diesel engine with low hours , almost new spudding pinion ,Tool guide , newer shock kit , guide pin & bushing , newer belt , approximately 500 feet of 3/4 inch drill line , approximately 400 feet of 3/8 inch sand line . Same owner the last 20 years . Mounted on a 1994 GMC Top Kick , 3116 Cat diesel engine , 5/2 speed transmission ,good tires .

Comes with a socket , stem , 6 inch bit , and bailer .

Located in central Alabama

(( SOLD ))Bucyrus Erie 22W Series 1 mounted on a 1987 Ford F8000 DRILL READY ****WITH TOOLING

 Bucyrus Erie 22W Series 1 ,sn#1163XX  ,Approximately 250 feet of 3/4 inch drill line , approximately 250 feet of 3/8 inch sand line , newer spudding pinion , new steel made bull reel drum , tool guide , newer heel sheave , newer shock kit assy. , Stainless Steel fuel tank , Isuzu 4 Cylinder diesel deck engine .

Mounted on a 1987 Ford F8000 ,3208 Cat engine ,5 speed , 2 speed rear end ,tandem axle ,air brakes , good front and rear tires ,** engine does use some oil , but is a good running engine . Rig is sitting on a bed ,with 4 foot storage area between truck and rig for tools .

Comes with the following tooling :

Socket , stem ,2- 8 inch bits ,3-bailers ,J wrenches , drive clamps.

rig is DRILL READY

((( SOLD ))) $6,500.00 Cyclone model 30

Cyclone model 3 cable tool drilling rig , has a 15 foot derrick ,plus another 15 foot section , it will drive 20 foot pipe , elevator shaft drilling rig , small cable tool drilling rig ,3 line drilling rig ,Continental Red Seal 4 cylinder gas engine .

No tools

Located in Kentucky .

Bucyrus Erie 21W , 2 line machine , GOOD PARTS RIG .

Bucyrus Erie 21 W  ,2 line machine ,good parts rig .

 located in Florida

SOLD 71 Speedstar , 240- 6 cylinder ,running condition , will sell mounted orun mounted on a 6X6 DRILL READY

71 Speedstar ,240- 6 cylinder Industrial gas engine , approximately 2,500 feet of 5/8 drill line , approximately 2,500 of 3/8 inch drill line .1 cathead , casing strut , 2 jacks on the back , comes with 2 sets of tooling . 3 & 5 inch tooling , and wrenches , mounted on a 6X6 in good condition , drilling condition .  Located in Kentucky .

Waiting on more photos ,contact for information .

OFF MARKET Bucyrus Erie 60L mounted on a 1992 Kenworth

Bucyrus Erie 60L , rig is completely guarded , 4 cylinder Perkins diesel engine , 4 hydraulic jacks , really great condition rig ,mounted on a 1992 Kenworth ,Detroit Diesel , tandem axle .

Located in Washington

Priced at $57,500.00 FIRM PRICE

Can require additional photos for completely

serious buyer .Serious buyers can contact me on website contact page .

Walker Neer S33 (((( Currently off the market ))))

Waukesha 6 Cylinder
Waukesha 6-cylinder engine, good clutches, 900 feet of 7/8-inch drill line, 900 feet of sand line, triple sheave casing block, tandem axle, no rust, comes with a lot of tooling. Rope sockets, 4 stems, 3 jars, 6, 8, and 10-inch bits, mostly 3x4 pin size. Circle Jack, 4 pair of wrenches, rod elevators, manual spyder with inserts, and additional tooling. Rig is located in Texas, with the same owner for the last 30 years.